Traxxas Steering Bellcranks/Servo Saver, Spring, Horn, Retainer

This is the Steering Bellcrank Set for the Traxxas Slash 4X4.

FUNCTIONS:
Composite nylon construction
Replaces a worn or damaged bellcrank set
May likewise be set up on the Traxxas Rustler, Outlaw and 2WD Slash
    designs (assembled in various configurations depending on design)

INCLUDES:
One Left Bellcrank Lower
One Left Bellcrank Upper
One Right Bellcrank
One Draglink
One Spring
One Spring Retainer
2 Servo Arms
2 Shoulder Screws
2 3x15 Counter Sunk Machine Screws
2 Hollow Balls
Four Bushings
Guideline Sheet

REQUIRES:
Assembly and setup following the design handbook and included
guideline sheet

Right here is a wonderful item that several others have bought at the very same time.

5 X 11 X 4Mm Ball Bearing (2) Blue Rubber Shield R Evo

This is a 2 pack of 5X11mm Ball Bearings for the Traxxas Revo.

FEATURES:
Metal bearing construction
Blue rubber dirt shields

INCLUDES:
(2) 5X11mm ball bearings, Part #5116

SPECIFICATIONS:
Inside diameter: 3/16" (5mm)
Outdoors diameter: 7/16" (11mm)
Width: 5/32" (4mm)

This item is often bought with the above pointed out item.

Extended Fr/Re Body Mounts Slash 2WD

This is the optional Pro-Line Extended Body Mount Kit for the
1/10 scale Traxxas Slash 2WD Short Course Trucks.

FEATURES:
Adjustable front and rear body mounts allow a wide array of bodies
    to be used including rally car bodies
Constructed of nylon, black in color
Screw-on body install system removes metal clips

INCLUDES:
Front and Rear Body Installs and Publishes with Mounting Hardware

The below item also pairs really well with the item being talked about.



The SW0231MG is a budget plan friendly water resistant digital servo with fantastic torque for numerous applications. This brushed servo functions a speed of .17 and 208.0 oz-in of torque 6.0V. It combines leading edge technology with super high 12-bit (4096) resolution and metal gears for your higher accuracy when evading puddles. This is a fantastic upgrade if your planning to drive your RC automobile in any condition...rain, sleet, or snow.

Functions:

• Integrates leading edge
  technology with super high 12 bit (4096) resolution and metal gears.
• Waterproof.
• Brushed motor
• Incredibly strong metal gears guarantee long-life and durability.
• Our servos are completely green ? from products to production, these servos are environmentally friendly.
• Ideal for RC cars, trucks, buggies, and boats.

Dimensions(mm): 41.8x20.2x42.9
Weight(g): 66
Speed(@6.0V sec/60): .17
Torque(@6.0V oz-in): 208.0
Equipment: Metal
Bearing: 2BB
Case: Plastic
25 Tooth Spline
IP Rating: 67
Frequency: 200-250hz
Pulse Width Frequency: 1520

This item is often bought with the above pointed out item.

Slash 2Wd Low Cg Chassis Conversion Kit

This is the optional Low CG Conversion Kit for the
1/10 scale 2WD Traxxas Slash.

FEATURES:
Reduces the chassis 1" (25.4mm) for better handling and higher
    cornering speed
Holds battery and electronic devices as deep in chassis as possible
45% lower battery position

INCLUDES:
Chassis
Lower Chassis
2 Nerf Bars
Battery Hold Down with Front and Rear Retainers
2 Front Shock Springs
Hardware and Instructions

This item is often bought with the above pointed out item.

Nerf Bars, For Traxxas Lcg Slash 2Wd, Blue

These are the optional RPM Nerf Bars in Blue for the 2WD Traxxas LCG Slash.

FEATURES:
Engineering grade nylon construction
Replaces the Traxxas #5833, #5833A & #5833G nerf bars
Designed particularly for the low center of gravity (LCG) Slash
    chassis
Additional cross bracing to enhance rigidity while absorbing impact
    energy

INCLUDES:
Left and Right Nerf Bars in Blue